Supplies NEEDED
6 one l/i" head pins
2" four x 1 mm sterling silver rectangle wire Two one' parts of sterling silver chain Two pearl beads
Two 1.four mm round sterling silver beads Two sterling silver ear wires
Instruments NEEDED
Ruler
Marker
Jeweler's noticed or tin snips Protection glasses Really hard, flat surface Awl
Hammer /Ίί" drill little bit
Handheld rotary tool, flex shaft, or drill press File
Great grit sanding pad
Ring mandrel
Rawhide mallet
Two pairs of chain nose pliers
Wire cutters or tin snips
Round nose pliers
one.Use the ruler to measure and mark two Γ parts of 4 x 1 mm rectangle sterling silver wire.
two.Using a jeweler's noticed or tin snips, Slash the 4 x one mm rectangle sterling silver wire into two Γ lengths.
3.File Every single end in the one" rectangle wire pieces to get rid of any burs or tough edges; You should use the file to around the ends in the rectangle wire parts if you want. Make use of a great grit sanding pad to go more than the world in which you have filed to clean the sides and remove any file marks.
4.Utilize the ruler to measure and mark '/*’ from Each and every conclusion from the Γ items of rectangle wire and put a mark in the center in the wire. This tends to be where you drill the holes to slide The pinnacle pins through.
5Next, put with your basic safety Eyeglasses! Then location the Γ rectangle wire items on to a hard, flat surface area. Position the point from the awl about the mark that you choose to produced /(." from Every single close from the rectangle wire items, and make use of a hammer to firmly strike at the time on the top in the awl. This could make a pilot gap for drilling holes in to the rectangle wire.
6.Utilizing a drill little bit. drill holes into each stop on the rectangle wire parts with a handheld rotary Instrument, flex shaft, or drill push (when still sporting your security Eyeglasses!).
seven.Use the file or good grit sanding pad to eradicate any burs or tough edges remaining from drilling holes into the rectangle wire pieces.
8.Curve equally Γ parts of rectangle wire right into a condition using a ring mandrel and rawhide mallet. If you do not have a ring mandrel and rawhide mallet, use two pairs of chain nose pliers. Keeping just one pair in each hand, grasp Every stop on the Γ rectangle wire piece from the chain nose pliers and Carefully bend the rectangle wire into a “C shape, aligning the holes which you drilled on Every single conclusion of your Γ rectangle wire pieces. Compare each in the C-formed rectangle wire items and change the curves so that they're identical in size.
Set these aside.
9.Make use of the ruler to measure the chain into Γ items. Make use of the wire cutters to chop the chain, and established these parts apart.
ten.Place a head pin through a pearl bead and after that include a single 1.four mm sterling silver bead.
eleven.Make use of the ruler to evaluate and mark /t" earlier mentioned the best bead on The pinnacle pin. With wire cutters or tin snips, Slash the head pin wire Yu," above the top bead.
12.Using the chain nose pliers, bend the head pin wire next to the very best bead at a 90-degree angle.
13.Hold the head pin With all the pearl bead along with the silver bead on it in a single hand Together with the wire that you just bent pointing towards you. Utilizing the spherical nose pliers, grip the tip of The top pin wire that is certainly pointing towards you and roll it from you (imagine turning the ignition essential to start out your automobile). Launch the pliers from The top pin wire. At this time, the opening while in the loop at the highest of The top pin wire must be substantial ample to slide the Γ size of chain on it ahead of closing the loop of The top pin. After you include the chain, use the round nose pliers to grasp the loop of the men's jewelry head pin wire and roll it closed. You can use the spherical nose or chain nose pliers to regulate The form with the loop at the highest of The top pin if you must.
14.Repeat this stage on the second pearl and silver bead. Set these aside.
fifteen.Position a head pin from the gap drilled into one particular conclude in the rectangle wire “C* shape with the bottom or flat end on The within curve of your rectangle wire *C* condition. Utilize the ruler to evaluate and mark The top pin s/u.m over the rectangle wire. With wire men's jewelry cutters or tin snips, Reduce the head pin wire above the best with the rectangle wire.
sixteen.Make use of the chain nose pliers to bend the head pin wire next to the rectangle wire in a ninety-diploma angle.
17.Using the men's fashion rings chain nose pliers in one hand, keep The underside or flat spot of The top pin firmly towards the rectangle men's fashion rings wire with the head pin wire that you bent pointing towards you.
With the other hand, make use of the rings for men round nose pliers to grip the end of The pinnacle pin wire and roll it faraway from you. Launch The top pin wire. At this point, the opening during the loop of The pinnacle pin wire need to nevertheless be big enough to slide the tip website link from the 1' chain on to iL Now incorporate the chain for the loop of the head pin. after which you can utilize the round nose pliers to grasp the loop of the head pin wire and roll it shut. You should utilize the round nose or chain nose pliers to adjust The form with the loop at the very best of the head pin.
eighteen.Repeat this method on another hole during the C-formed rectangle wire. As opposed to adding the one * size of chain Using the pearl and the sterling silver bead, insert the ear wire at another finish. Slip the ear wire on to the loop of The top pin prior to closing the loop.
19.Repeat the previous techniques on the next earring.
